|
|
|
|
|
|
|
|---|
 Green Air Integrated Cooling Thermostat & Dehumidistat/4 outlet
This CT-DH-1 is designed to turn On and Off exhaust fans and/or intake fans to remove unwanted atmosphere due to heat or humidity. This device is intended as a cooling and dehumidifying control. This controller is ideal for situations where excess heat and humidity need to be exhausted. Internal sensors will allow a 7 temperature comfort zone and a 7% humidity spa(differential) between the time the fans go off and come back on again. When either temperature or humidity exceeds the dial settings, all four outlets will turn ON, activating any cooling or exhaust equipment plugged into the controller. | | Item # | Description | Price | Add to Cart |
|---|
| 702330 | (CT-DH-1) INTEGRATED COOLING | $205.00 |  |
|
|
|---|
 Green Air Independent Cooling & Heating Thermostat/4 outlet model CT-HT-2
This controller features fully independent sensors for cooling and heating equipment. The cooling thermostat activates the left outlets of the controller and the heating thermostat activates the right outlets. If you require a tighter control of your temperature than the internal heating \ cooling thermostats allow, alternate sensors are available with a 3 differential (External Coil | | Item # | Description | Price | Add to Cart |
|---|
| 702350 | (CT-HT-2) INDEPENDENT COOLING & HEATING | $205.00 | |
|
|
|---|
 Green Air Synchronized Cooling Thermostat/Dehumidistat/4 outlet - model CT-DH-3
It is highly important to keep your greenhouse environment functioning properly, light timers, temperature control and C02 regulators are all items that help you take care of this. We carry a wide variety of products in popular brands like Titan Controls, Sentinel and Harvest-Master. | | Item # | Description | Price | Add to Cart |
|---|
| 702335 | (CT-DH-3) SYNCHRONIZED COOLING | $228.00 | | | 702340 | (CT-DH-3P) SYNCHRONIZED COOLING W/PHOTO | $285.00 | |
|
|
|---|
 The Micro Climate Controller MCC-1 is designed to perform all the major atmospheric and timed functions required in an automated growth environment including temperature, humidity, carbon dioxide enrichment, lighting and irrigation control. The controller incorporates an external coil cooling thermostat, a dehumidifying humidistat, a 24-hour clock timer, a photo-sensor and a repeat cycle timer. Automatic override and defeat systems coordinate controls to consider all possible variables. The MCC-1 is enclosed in a black anodized, brush finish aluminum housing. All connections are standard 3-prong grounded plugs and receptacles. Operates on 110VAC with 15 Amp switching capacity. | | Item # | Description | Price | Add to Cart |
|---|
| 702355 | (MCC-1) MICROCLIMATE CONTROLLER SYSTEM | $793.25 | |
|
|
|---|
 Control humidity automatically and accurately with Green Air Products Total Humidity Controller. The THC can be switched between humidify and dehumidify to remove unwanted atmospheric moisture accumulating within an enclosed area or to add needed moisture to the air by means of humidification. In the dehumidifying mode high humidity conditions will activate fans or other dehumidifying apparatus until level drops approximately 7% in relative humidity. At this point dehumidifying equipment is disabled until humidity increases again 7%. In the humidifying mode this control operates fogging or other humidifying equipment by activating switches, motors, valves or pumps. Humidifiers can be precisely controlled according to atmospheric humidity to create ideal conditions for any environment. | | Item # | Description | Price | Add to Cart |
|---|
| 702375 | (THC-1) TOTAL HUMIDITY CONTROL | $147.25 | Add to Cart |
|
|
|---|
 The CST-1 has solved the age old problem of accurate short cycle timing. The only unit of its kind designed specifically for the control of grow systems. Easy to set and operate. Solid state time counter with adjustable frequency and duration. The CST-1 function timer has many uses and only a few of them include: fogging or misting, spray stakes or drip system timing, air pumps, CO2 equipment and intake exhaust fan control. | | Item # | Description | Price | Add to Cart |
|---|
| 702379 | (CST-1) CHRONOMETRIC SEQUENTIAL TIMER | $261.25 | |
|
|
|---|
 The Cyclestat 4P is perfect for plant zone environments, reptile habitats or any other application requiring automatic short cycle switching. No programming required. Easy to set and operate. Microprocessor time counter with adjustable frequency and duration. The Cyclestat 4P timer has many uses. Only a few of them include: fogging or misting, spray stakes or drip system timing, air pumps, CO2 equipment and intake or exhaust fan control. The Cyclestat may be set for interval and cycle of timed events. Interval is the time between ON cycles. The interval knob may be set from 5 minutes to 8 hours. Set this for desired time between functions. Cycle is the length of time that a specific function or condition must be maintained. Cycle may be set from 5 seconds to 30 minutes. | | Item # | Description | Price | Add to Cart |
|---|
| 702385 | (CYCLESTAT-4P) REPEAT CYCLE TIMER | $180.95 | Add to Cart |
|
|
|---|
These time switches are designed to operate high load lighting equipment. They consist of a premium quality precision synchronous clock motor and a high amperage switching circuit. These controllers are housed in black anodized brush finish aluminum enclosures which will not break, chip or corrode. Operates with a maximum combined outlet switching capacity of 40 amps. Plug or wire the power cord into a receptacle capable of handling the maximum total combined amperage draw of your equipment load. Plug lighting equipment into outlet receptacles located on each side of controller. Timer has 96 non-detachable 15 minute on\off trippers.
The LT4-120 provides four 10 amp outlets, and is capable of controlling up to four 1000 watt lights each.
The LT4-240 offers four 5 amp outletsand is capable of controlling up to four 1000 watt lights each.
| | Item # | Description | Price | Add to Cart |
|---|
| 702390 | (LT4-120) 4 LIGHT TIMER 120V | $318.25 | | | 702395 | (LT4-240) 4 LIGHT TIMER 240V | $380.00 | |
|
|
|---|
These time switches are designed to operate high load lighting equipment. They consist of a premium quality precision synchronous clock motor and a high amperage switching circuit. These controllers are housed in black anodized brush finish aluminum enclosures which will not break, chip or corrode. Operates with a maximum combined outlet switching capacity of 40 amps. Plug or wire the power cord into a receptacle capable of handling the maximum total combined amperage draw of your equipment load. Plug lighting equipment into outlet receptacles located on each side of controller. Timer has 96 non-detachable 15 minute on\off trippers.
The LT8-240 provides eight 5 amp 240 volt outlet receptacles, each capable of powering up to 1000 watts of lighting equipment.
| | Item # | Description | Price | Add to Cart |
|---|
| 703400 | (LT8-240) 8 LIGHT TIMER 240V | $441.75 | Add to Cart |
|
|
|---|
 This new easy to install and to operate CO2 enrichment controller is factory calibrated and inspected for optimum performance. The SPC-1 is designed with a photo sensor to defeat CO2 enrichment during dark periods and a large easy to read real-time LED display. The SPC-1 also is programmed with a preset differential (hysteresis) of 20 PPM and offers an elevation adjustment feature to fine tune performance. Quick Start Installation Instructions are available in English and Espaol. Like all of Green Air Products high quality controllers, the SPC-1 is constructed with durable components and a rust and scratch resistant, black anodized aluminum chassis to ensure that this controller will perform as expected for years to come. Operates on 120 Volts AC with 12 Amps switching capacity. | | Item # | Description | Price | Add to Cart |
|---|
| 703423 | (SPC-1) CO2 SET POINT CONTROLLER | $631.75 | |
|
|
|---|
These Green Air Products systems are a breakthrough in CO2 detection and control. The CDMC-6 system is designed to sample the air and learn the characteristic of your space, then make adjustments as necessary to ensure a constant level of CO2. The CDM-6000 monitor employs a passive infrared sensor which samples the air once every second and then sends the sample data to the CDDS-2 sequencer. The CDDS-2 then activates or deactivates your CO2 enrichment or venting (exhaust) equipment to maintain desired CO2 PPM. The CDDS-2 uses a sophisticated adaptive algorithm or “Overshoot Protection Logic” to learn the dynamics of the space being controlled. This allows the systems to avoid dramatic overshoots inherent to set point controllers or timed CO2 enrichment. These learned parameters are stored in the memory, even when the ‘POWER’ is off, or until you reset the unit.
The CDMC-6 system offers a large LCD screen displaying the current CO2 levels in PPM. Set your desired CO2 level, ‘Hysteresis’ and ‘Elevation’ to maintain precise levels without guesswork.
The CDMC-6 system can be using for enriching or venting CO2 and incorporates a photosensor to defeat CO2 during dark periods (Night).
| | Item # | Description | Price | Add to Cart |
|---|
| 703415 | (CDMC-6) CDDS-2 & CDM-6000 SENSOR | $940.50 | |
|
|
|---|
 Green Air Products bottled CO2 emitter systems combine a forged brass flow gauge regulator with a UL/CE/CSA certified emitter solenoid valve. These systems offer a flow range from 7-20 SCFH. The BCDE systems come with 10 feet of clear tubing with spring clamps, a grounded 6ft 120 volt power cord. | | Item # | Description | Price | Add to Cart |
|---|
| 702404 | (BCDE-1) BOTTLE CO2 REGULATOR W/SOLENOID | $308.75 | |
|
|
|---|
 Replacement adaptor for CO2 generators. | | Item # | Description | Price | Add to Cart |
|---|
| 703476 | (T12VDC) 12 VOLT DC ADAPTOR FOR CO2 | $26.50 | Add to Cart |
|
|
|---|
 Green Air Replacement CO2 Hose | | Item # | Description | Price | Add to Cart |
|---|
| 702435 | CO2 HOSE | $55.00 | Add to Cart |
|
|
|---|
 Carbon dioxide generators operate by burning carbonaceous fuels such as propate or natural gas. The burners us in Green Air Products C02 generators are specially designed to maximize the production of C02 and minimize heat as a by-product. Green Air Products generators provide C02 far more economically than any other means of enrichment. A constant burning pilot is used to ignit the gase when the generator is turned on. A thermocouple is used to monitor the pilot flame. If the pilot flame is lost, a safety valve will close so that unburned fuel will not be released into the enclosure. C02 Generator operatios may be automatically functioned according to actual ambient values when installed in conjunction with the CDMC. The generators may be controlled with timers such as the Cyclestat 4P. This control device continually samples the level of carbon dioxide in the growing area and activates the generator whenever C02 levels do not meet your predetermined values. Generators are easily installed, dependable and efficient. Transformer included. Operates on 110 volt AC. | | Item # | Description | Price | Add to Cart |
|---|
| 703430 | (CD-3LP) CO2 GENERATOR PROPANE 3 cuft/hour | $484.50 | | | 703455 | (CD-3NG) CO2 GENERATOR NATURAL GAS 3 cuft/hour | $517.75 | | | 703435 | (CD-6LP) CO2 GENERATOR PROPANE 6 cuft/hour | $570.00 | | | 703460 | (CD-6NG) CO2 GENERATOR NATURAL GAS 6 cuft/hour | $589.00 | | | 703440 | (CD-12LP) CO2 GENERATOR PROPANE 12 cuft/hour | $650.75 | | | 703465 | (CD-12NG) CO2 GENERATOR NATURAL GAS 12 cuft/hour | $665.00 | | | 703450 | (CD-36LP) CO2 GENERATOR PROPANE 36 cuft/hour | $802.75 | | | 703475 | (CD-36NG) CO2 GENERATOR NATURAL GAS 36 cuft/hour | $821.75 | |
|
|
|
Hydroponics Explained DVD |
|---|
The complete hydroponic growing guid... |
|
Read more »»»
|
|
Graduated Measuring Cups |
|---|
General purpose measuring cups. Chem... |
|
Read more »»»
|
|
|
| ©2009-2010
Hydrobarn
• Conditions of Use • Copyright • Privacy Policy • Site Map |
