Environmental Controllers » Titan Controls

• Digital control board delivers precision CO2 control. Maximize your CO2 production while minimizing CO2 or LP consumption.
• Adjust CO2 set point, modify elevation or calibrate with just two buttons.
• Controls any CO2 equipment that is operated by 120 volt power.
• Durable powder coated, steel enclosure will stand up to the toughest conditions.
• Adds CO2 only during daylight period using the controllers integrated photocell.
• 50 parts per million (ppm) deadband/hysteresis built into set point.
• Memory retains controllers setting even when the power is off
• 15 amp maximum.

• Compatible with Titan Controls CO2 Controller or other 120 volt controllers and timers.
• Precision Accuracy Flow Meter - .5 to 15 SCF/hour.
• CO2 helps increase overall plant growth.
• Features heavy-duty solenoid valve.
• Brass construction for long-lasting dependability and durability.
• Includes 12’ of CO2 dispensing line.
• Powered by 6’ - 120 volt grounded power cord.
• Two plastic tank washers included.
• High quality oil-less pressure gauge.
• 3 Year Warranty.

• Aluminum case and solid brass expansion chamber.
• Completely enclosed heating element.
• Solid brass fittings for C02 cylinders, CGA 320.
• Power consumption = 100 watts.
• Electrical = 115 Volts, 50/60 hertz, single phase.
• Capacity = 90 scfh maximum.
• NEMA 5-15 grounded power cord.

• Allows precise humidity control.
• 0% - 90% range lets the user adjust humidity level to ideal settings.
• Change from ‘humidification’ to ‘dehumidification’ with just a flip of the switch.
• Controls any 120 volt humidifier, dehumidifier or fan. Durable powder coated, steel enclosure will stand up to the toughest conditions.
• Grounded piggy-back cord is safe and easy to use. Ventilation louvers help avoid water accumulation and possible damage to the unit.
• Built in 4% split differential
• 15 amp maximum.

• Activate your lamp cooling fan or night exhaust fan with this straightforward, easy to use controller.
• Goes from ‘DAY’ to ‘NIGHT’ mode with a flip of the switch.
• Built using durable powder coated steel enclosure with the highest quality components available.
• 15 amps/120 Volt/60 Hz.
• 3 year warranty.

• Digital control board allows for precise timer settings. 3 seconds to 30 minutes “on-time” and 3 minutes to 8 hours “off-time”.
• Very easy to set and use.
• Will run CO2 with switch set to ‘day’ position.
• Use to run a pump with the switch in the ‘both’ position.
• Will run an exhaust fan with switch set to ‘night’ position. Durable powder coated, steel enclosure will stand up to the toughest conditions.
• The green LED light on the front of the controller shows the user when the timer is ‘on’.
• 15 amp maximum.

• This controller will run four (4) HID lights at 120 Volts – Maximum 4000 Watts.
• 120 Volt accessory timed outlet to activate in-line fans to cool your lamps.
• German built 24 hour timer with 15 minute non-detachable setting tabs.
• 3 screws in back panel makes timer easy to wire into your power system.
• On/Off switch that makes lamp replacement easy.
• Four NEMA 5-20 outlets.
• Durable powder coated steel chassis.
• 120 Volt/50 Amps/60 Hz.
• 3 year warranty.

• This controller will run four (4) HID lights at 120 Volts – Maximum 4000 Watts.
• 120 Volt accessory timed outlet to activate in-line fans to cool your lamps.
• Plug relay trigger cord set into 24 hour wall timer.
• 3 screws in back panel makes timer easy to wire into your power system.
• On/Off switch that makes lamp replacement easy.
• Four NEMA 6-15 outlets.
• Durable powder coated steel chassis.
• 120 Volts/ 50 Amps/60 Hz.
• 3 year warranty.

• This controller will run four (4) HID lights at 240 Volts – Maximum 4000 Watts.
• 120 Volt accessory timed outlet to activate in-line fans to cool your lamps.
• German built 24 hour timer with 15 minute non-detachable setting tabs.
• 3 screws in back panel makes timer easy to wire into your power system.
• On/Off switch that makes lamp replacement easy.
• Universal outlets allow total flexibility.
• Durable powder coated steel chassis.
• 240 Volts/ 30 Amps/60 Hz.
• 3 year warranty.

• This controller will run four (4) HID lights at 240 Volts – Maximum 4000 Watts.
• 120 Volt accessory timed outlet to activate in-line fans to cool your lamps.
• Plug relay trigger cord set into 24 hour wall timer.
• 3 screws in back panel makes timer easy to wire into your power system.
• On/Off switch that makes lamp replacement easy.
• Universal outlets allow total flexibility.
• Durable powder coated steel chassis.
• 240 Volts/ 30 Amps/60 Hz.
• 3 year warranty.

This product controls temperature, humidity and CO2 in you grow area at your preferred settings.  The built in ten (10) minute ‘CO2 delay’ feature deactivates the CO2 equipment if settings are exceeded by using a digitally based control system. The software polls the temperature and humidity setting ten minutes after the CO2 outlet is defeated to verify that the temperature and humidity are too high, and then activates your exhaust fan, A/C or dehumidifier to lower the conditions under the settings. If the temperature or humidity drops below the set point during the 10 minute ‘CO2 delay’, then the exhaust/dehumidification process is defeated and the ‘CO2 ON’ outlet is reactivated, saving your valuable CO2 and keeping it amongst the plants where it belongs.

The Kronus 2 activates an exhaust fan, A/C or dehumidifier if the temperature or humidity exceeds the preferred settings. The ‘CO2 ON’ feature is only activated during daylight periods to dose CO2 when your plants are able to uptake it and is disabled during the nighttime hours or when the humidity or temperature exceeds the preferred settings. Plug your exhaust fan, dehumidifier  or A/C into the ’Exhaust Fan Output’  and plug your CO2 tank with emitter system or CO2 generator into the ‘CO2 Output’ and you’re all set!

• Controls temperature, humidity and CO2 in your garden.
• Activates “CO2 ON’ outlet only during daylight hours.
• Ten (10) minute ‘CO2 delay’ feature allows maximum CO2 coverage with minimum CO2 waste.
• Easy to understand.
• Highlighted ‘Grow Zones’ for ease of use.
• 25 foot modular remote temperature and humidity sensor.
• Only the highest quality components are used.
• Improves your yield by creating the perfect environment for your plants.
• Controllers designed by our industry, for our industry.
• 15 Amps/120 Volts/60 Hz.
• 3 year warranty.

This product controls temperature and CO2 in you grow area at your preferred day and nighttime settings. The built in ten (10) minute ‘CO2 delay’ feature deactivates the CO2 equipment if the daytime temperature setting is exceeded by using a digitally based control system. The software polls the temperature setting ten (10)minutes after the CO2 outlet is defeated to verify that the temperature is too high, and then activates your exhaust fan or A/C to lower the conditions under the setting.  If the temperature drops below the set point during the ten (10) minute ‘CO2 delay’, then the exhaust process is defeated and the ‘CO2 ON’ outlet is reactivated, saving your valuable CO2 and keeping it amongst the plants where it belongs.

The Kronus 3 activates an exhaust fan or A/C if the temperature exceeds the preferred settings. The ‘CO2 ON’ feature is only activated during daylight periods to dose CO2 when your plants are able to uptake it and is disabled during the nighttime hours or when the temperature exceeds the preferred settings. Plug your exhaust fan or A/C into the ’Exhaust Fan Output’  and plug your CO2 tank with emitter system or CO2 generator into the ‘CO2 Output’ and your daytime conditions are under control. For nighttime conditions, you can plug a nightlight into the ‘Night Only Output’ so you can work in your garden after hours or plug a timed exhaust fan into the ‘Night Only Output’ to ventilate your garden during the nighttime hours. The ‘Night Heat Output’ is used to plug a heater into to keep your plants from getting the night chills. The Kronus 3 is the ultimate in temperature controls!

• Controls day and night temperature and CO2 in your garden.
• Activates “CO2 ON’ outlet only during daylight hours.
• Ten (10) minute ‘CO2 delay’ feature allows maximum CO2 coverage with minimum CO2 waste.
• Features a ‘Night Only’ and ‘Night Heat’ outputs to assist the gardener with the maintenance of the garden after the lights have turned off.
• Easy to understand.
• Highlighted ‘Grow Zones’ for ease of use.
• 25 foot modular remote temperature sensor.
• Only the highest quality components are used.
• Improves your yield by creating the perfect environment for your plants.
• Controllers designed by our industry, for our industry.
• 15 Amps/120 Volts/60 Hz.
• 3 year warranty.

This product controls temperature, humidity and CO2 in you grow area at your preferred daytime and nighttime settings. The built in ten (10) minute ‘CO2 delay’ feature deactivates CO2 equipment if day temperature or humidity setting is exceeded by using a digitally based control system. The software polls the temperature and humidity setting ten (10) minutes after the CO2 outlet is defeated to verify that the temperature or humidity is too high, and then activates your exhaust fan or A/C to lower the conditions under your settings. If the temperature drops below the set point during the ten (10) minute ‘CO2 delay’, then the exhaust or A/C process is defeated and the ‘CO2 ON’ outlet is reactivated saving your valuable CO2 and keeping it amongst the plants where it belongs. The ‘Night Only’ and ‘Night Heat’ outputs provide a nightlight or exhaust fan and heat for your enclosure during the nighttime period. This provides the customer with 24 hour temperature and humidity control in their garden.

The Kronus 4 activates an exhaust fan or A/C or if the temperature or humidity exceeds the preferred settings. The ‘CO2 ON’ feature is only activated during daylight periods to dose CO2 when your plants are able to uptake it and is disabled during the nighttime hours or when the humidity or temperature exceeds the preferred settings. Plug your exhaust fan or A/C into the ’Exhaust Fan Output’  and plug your CO2 tank with emitter system or CO2 generator into the ‘CO2 Output’ and your daytime conditions are under control. For nighttime conditions, you can plug a nightlight into the ‘Night Only Output’ so you can work in your garden after hours. The ‘Night Heat Output’ is used to plug a heater into to keep your plants from getting the night chills. The Kronus 4 gives the expert gardener the top shelf controller they’re looking for to maintain their garden!

• Controls CO2, DAY/NIGHT temperature and humidity in your garden.
• Activates "CO2 ON’ outlet only during daylight hours.
• Ten (10) minute ‘CO2 delay’ feature allows maximum CO2 coverage with minimum CO2 waste.
• Features a ‘Night Only’ and ‘Night Heat’ outputs to assist the gardener with the maintenance of the garden after the lights have turned off.
• Easy to understand.
• Highlighted ‘Grow Zones’ for ease of use.
• 25 foot modular remote temperature and humidity sensor.
• Only the highest quality components are used.
• Improves your yield by creating the perfect environment for your plants.
• Controllers designed by our industry, for our industry.
• 15 Amps/120 Volts/60 Hz.
• 3 year warranty

• Remote sensor is specifically designed for the Kronus 3 controller.
• Provides a digitally based signal that reacts quickly to changing temperature levels in your garden.
• Plastic enclosure resists dust and moisture.
• Integrated photocell allows the operator to monitor both day and night conditions.
• Green LED indicates that sensor is functioning properly.
• May be located up to 50 feet from the controller.

• Remote sensor is specifically designed for the Kronus 1, 2 & 4 controllers.
• Provides a digitally based signal that reacts quickly to changing temperature and humidity levels in your garden.
• Plastic enclosure resists dust and moisture.
• Integrated photocell allows the operator to monitor both day and night conditions.
• Green LED indicates that sensor is functioning properly.
• May be located up to 50 feet from the controller.

For use with Titan Controls Kronus models. Optional 10, 25 and 50 foot cables are available.

• Cat 5e cables.
• RJ-45 plugs.
• UL Listed.
• Booted connection to avoid corrosion.